PFC Brake Pads for Track Cars: Which Compound Owners Run, Car by Car
PFC pads are the ones you hear before you see them. Walk down a paddock on a busy HPDE weekend and the squeal coming off a BMW or a Porsche in the grid line is often a set of 08s. Owners put up with the noise because the pads last, the pedal is consistent, and the same compound number means the same thing on a Miata as on a GT3.
This guide is for track cars only. It is built around what owners actually run, read from the forums where they argue about it — ft86club, f87.bimmerpost, m3post, r3vlimited, Rennlist, 911uk and Porsche Club GB, mazdaracers and Grassroots Motorsports — checked against what PFC itself says. Each main compound has its own deeper article. If you want PFC's own descriptions side by side, start with the PFC compounds compared.
First, PFC does not publish temperature ranges
Hawk prints operating and optimal temperatures for its pads. PFC does not. Its compound sheets carry friction-versus-temperature curves with no numbers on the friction axis, so there is no honest way to put PFC compounds on a temperature chart. What PFC does say is how each compound behaves as it heats up, and that turns out to be the useful part: whether the bite stays flat, rises, or falls away when the pad gets hot.
PFC also groups its compounds into families, which makes the range easier to read than the numbers suggest. 11 sits in the sprint family with 01. 08 heads the high-temperature, endurance family, and 97 is part of that same family. 13 is the high-bite family. Z-Rated is the fast-road pad.
Quick picks
- First track days, any car we list — 08. It is PFC's longest-wearing pad and the one owners keep calling bulletproof. Expect it to squeal on the street.
- Time trial, sticky 200-treadwear tires or more power — 11. Owners who overheat 08s on stock brakes move here, and it is quieter.
- Modern Porsche GT cars (991 / 992 GT3, 981 GT4) — 11. PFC does not make 08 for the 991.2, and 11 is what most GT4 owners run.
- You want the most bite and the car is set up for it — 01, where it is still made in your shape. In many BMW shapes it has been replaced by 11.
- Rear axle of a car that locks the rears — a calmer pad than the front: 97 where it still exists (NA Miata, early 911), or 332 on ABS cars.
- Carbon-ceramic rotors — not covered here. See the note further down.
The compounds side by side
These are PFC's own descriptions, shortened. PFC publishes no friction numbers or temperature ranges for any of them.
| Compound | PFC family | How PFC describes the torque | What owners use it for |
|---|---|---|---|
| 08 | High temperature / endurance | Slight friction rise with temperature; smooth initial bite; wears the longest of all PFC pads | HPDE, club racing, endurance; the drive-to-the-track pad |
| 11 | Sprint / medium distance | Developed from 01 with improved bite, modulation and release; rising friction with temperature | Time trial, sprint racing, modern Porsche GT cars |
| 01 | Sprint / medium distance | Good initial bite with very little torque rise with temperature | Racing; the old benchmark, now replaced by 11 in many shapes |
| 97 | High temperature / endurance (legacy) | Slight friction rise with temperature; "In many pad shapes, 97 has been replaced by 08" | Rear pad on cars that lock the rears |
| 13 | High bite / high torque | High bite in the first third of the stop; fade resistant | High-grip or downforce cars; some run it as a rear behind 01 |
The difference that matters most on track is between 08 and 11. Both are made in most shapes, they cost the same, and owners argue about them constantly. In short: 08 lasts longer and is gentler on the pedal, 11 holds up better when the tires and the speeds go up.
The ladder, in one paragraph each
08
PFC lists 08 for track days and driver education, and owners agree. The reputation is longevity. "The PFC08 is bulletproof. Far outlasted any other pad that I've tried," wrote an M2 owner on f87.bimmerpost; another said "they wear like iron." The limit shows up with sticky tires and more speed: an E90 M3 owner on m3post was "overheating the 08 compound on stock brakes and RS4 tires, leading to pad fade and accelerated wear on the front." The other complaint is street noise. Go deeper on 08 →
11
PFC built 11 from the 01 and calls it the replacement for it in many applications. It is the pad most owners mean when they talk about PFC on a GT4 — "most seem to run PFC11," as one Rennlist thread starter put it — and it is the step up from 08 for time trial. An m3post regular summed up the trade: "The 11 is quieter than the 08, so I prefer it, but the 08 will last longer when you're just getting started." Go deeper on 11 →
01
PFC still calls 01 "the standard by which all brake pads are judged": good bite and very little torque rise as it heats up. Owners remember it for the bite and the consistency. It has quietly disappeared from many BMW shapes, where 11 replaced it around 2015, but it is still made for some cars, including the FR-S and BRZ front. Go deeper on 01 →
97
PFC's own page now says "in many pad shapes, 97 has been replaced by 08 compound." Where it survives — the NA Miata rear, the early 911 front — its job is the rear axle: dealers recommend it as a rear pad for cars that tend to lock the rears. A Miata driver who ran it behind 01 fronts wrote that the rears were "good for over 50 track days." Go deeper on 97 →
What people run, car by car
This is the community picture, not PFC's. Where owners disagree, we say so, and where there is little data we say that too. The last column links the PFC shapes we list for that car. Shapes are shared across cars, so confirm yours before you order.
| Car | Getting started | Intermediate | Advanced / race | Our pads |
|---|---|---|---|---|
| Miata NA / NB | 08; "I start my newbies on PFC pads" (mazdaracers) | 11 front | 01 front, 97 rear on big brakes | 1.6: front 0525 (08) · rear 0458 (08) / 0458 (97) 1.8: front 0635 (08) / (11) · rear 0636 (11) / (97) No PFC pad for the NB Sport calipers |
| FR-S / BRZ / 86 (2013–20) | 08 front; owners report 08 rears can "upset the balance" | 08 street and track | 01 front, 13 rear on a big brake kit | Factory calipers: front 0929 (01) · rear 1124 (13) |
| BMW E30 | 08 | 08 or 11 | 08 (Spec E30) | Front 0278 (08) / (11) · Rear 0279 (08) |
| BMW E36 / E46 M3 | 08 | 11 (01 before it was dropped) | 11 or 08; 332 rear in Spec E46 | Front 0394 (08) · E46 M3 rear 0548 (08) / (332) E36 / E46 non-M rear 0396 (08) / (11) |
| BMW E9x M3 | 08 | 11 once 08s overheat on sticky tires | — | Rear 0919 (08) |
| BMW F87 M2, F80 M3, F82 M4 | 08 both ends, or 08 front with 332 rear | 11 | 11; 39 called "way too much bite" | Front 1609 (08) · Rear 1656 (08) Not the M2 Competition / CS calipers |
| Porsche 986 / 987 Boxster & Cayman | 08 (06 before it was retired) | 08 or 11 | Spec Boxster owners split on 08's initial bite | 986 base front 0737 (08) S / R front 0776 (08) / (11) Rear 0738 (08) / (332) |
| Porsche 996 / 997 Carrera | 08 — "squealed like crazy on the road" | 08 or 11 | — | 996 front 0776 (08) · Rear 0738 (08) |
| Porsche 996 / 997 GT3 | 08 (older threads) | 08 | 01 for bite (older threads) | Front 7819 (11) / (331) |
| Porsche 991 / 992 GT3, 981 GT4 (iron) | 11, or 331 front / 332 rear on a coach's advice | 11 — the GT4 consensus | 11 | Front 1773 (11) or 7721 (11) · Rear 7727 (11) / (332) |
| 991 GT3 Cup / 981 GT4 Clubsport | — | — | Dealer lists 11, 15 or 82 front; 11, 332 or 81 rear | Front 7968 (11) · Rear 7969 (11) / (332) |
| 992 GT3 Cup | — | — | 39 or 13 front, 11 or 01 rear (dealer advice) | Front 7797 (39) |
| Classic 911 (to 1983) | Little data | — | — | Front 0045 (08) / (11) / (97) · Rear 0031 (11) |
| Subaru WRX STI (2004–14 Brembo) | Little data | — | — | Rear 0109 (08) |
The tire decides when 08 runs out
Nobody publishes a weight or horsepower cutoff for PFC compounds. What owners describe instead is the point where the tire outgrows the pad. On street tires and most 200-treadwear tires, 08 is enough. "I don't think you're going to see a big difference between the 08 and 11 on a tire like the PS4S," wrote a Spec E46 racer on m3post. On stickier rubber the 08 starts to fade on stock brakes, and owners move to 11. An M2 owner put the other end bluntly: "I find that the PFC08s are good for street tires, but they cannot lock up the wheels with slicks."
Split friction: the calmer pad goes at the back
PFC designs some compounds specifically for the rear axle — 332 is "formulated with lower bite and torque for rear applications" and built for ABS cars — and dealers have long recommended 97 as a rear pad on cars that lock the rears. Owners follow the same rule. An M2 driver who ran 08 front with 332 rear wrote that, coming from Hawk DTC-70s, the PFCs had "better modulation, better pedal feel, and better balance."
The mistakes are on the other side. An FR-S owner with 08 fronts and a Hawk DTC-60 rear reported too much bite at the back, and a Brembo-kit BRZ owner found that 08s at both ends made the rears "heat up much quicker and upset the balance." If you are new, run the same compound at both ends, or put the milder pad at the rear, never the reverse.
What they cost you besides money
Noise. This is the most common complaint about 08, on every platform. "They are incredible loud," wrote an M2 owner; a 996 owner said they "squealed like crazy on the road but it doesnt bother me too much." Owners report 11 as quieter.
Dust. Heavy, and owners disagree on whether it eats wheel finish. An E36 M3 owner called 08 dust "corrosive to wheel finish"; an FR-S owner running 01 and 13 said his did not damage the paint.
Rotors. This is where owners disagree most. PFC claims "very low abraded disc wear" for 08 and "superior disc conditioning" for 11, and plenty of owners agree — a Miata racer credited PFC pads with "long rotor life". Others report the opposite: a 991 GT3 owner called 11 "really harsh on disc wear", and an FR-S owner said his 08s were "a bit hard on the disc, not that I mind." The pattern in the threads is that cold street miles wear rotors faster than hot track laps. Budget rotors with pads either way.
Bedding and switching compounds
PFC pads come pre-treated, but PFC still says "proper bedding is still required". On track its procedure is several stops of rising pressure from rising speeds on the first lap — six to ten per lap, usually done in a lap or two — then let the rotors cool as much as practical before parking. If the rotors carry another brand's transfer layer, PFC says it can take three to five laps.
Owners mostly find PFC easy to bed. A Miata driver wrote that PFC pads "are easy to bed and do not require their own transfer layer"; an M2 owner said there was "nothing special with bedding", though he did get some judder at first. Fresh fluid matters as much as the pads: see why we change brake fluid after every track day.
Two things to know before you order
Carbon-ceramic rotors. PFC makes some pads in the taller PCCB shape, but we could not find any PFC statement on running its race compounds on carbon-ceramic discs, and we will not guess. The common advice on Rennlist is Pagid RSC-1 on factory ceramics, or a conversion to iron rotors for track use. See our Pagid guide for RSC-1.
Street pads. "Carbon Metallic" is the name of PFC's friction material, used on every pad it makes, race pads included. It is also the name of PFC's everyday street pad line, which causes confusion. Z-Rated is PFC's step up from that street pad, sold for "fast road / track day" use; it is the lowest-friction line on PFC's chart, and dealers recommend it mainly as a street pad. If the car is driven to the track, run a street pad on the road and swap at the paddock.
The rest of the range
- 13 — PFC's high-bite sprint compound and the replacement for the old 03. For high-grip or downforce cars; one FR-S owner ran it as the rear behind 01 fronts.
- 331 / 332 — newer ABS-friendly endurance pads, 331 for the front and 332 for the rear. Dealers now suggest them for GT3, GT4 and F8x M cars. Owner reviews are mixed: one M2 owner was "extremely happy with the 332/331 combo"; another went back to 11.
- 39 — the highest average torque of any PFC compound, for GT3 and Cup cars. An M2 owner found it had "way too much bite in all temps" on a street-based car.
- 15, 81, 82 — Cup-car and Clubsport compounds. If you run one of those cars, you probably already know which one you want.
- 06 and 03 — retired. 06 was replaced by 08, 03 by 13. You will still see them recommended in older threads.
Pads we have ready to ship
These were in stock when we wrote this and fit cars from the table above.
Or browse by compound: 08, 11, 01, 97, all PFC brake pads, or the PFC two-piece rotors.
The Bottom Line
For most track cars on street or 200-treadwear tires, the answer is 08: it lasts, it is consistent, and it is what most owners in these threads run. Move to 11 when the 08s start to fade on sticky tires or a modern Porsche, because 11 holds up better and is quieter. Use 01 only where it is still made and you want the bite. Keep 97 and 332 for the rear axle. And put up with the noise, or swap to a street pad for the drive home.
If you are not sure which shape your car takes, read the first four digits off your old pads or the box — that is the shape, and the next two digits are the compound — or tell us the car, the caliper and what you do with it, and we will confirm before you order.
Related guides
- PFC 08 on track, car by car
- PFC 11: the new 01, and where it beats the 08
- PFC 01: the benchmark pad
- PFC 97 as a rear pad, and why 08 replaced it
- Best PFC brake pads compared
- Pagid brake pads for track cars, car by car
- Hawk brake pads for track cars, car by car
- How to choose track brake pads
- Track day brake fade: prevention and recovery





